PH211-1 HB

The PH 211-1 HB, manual band sawing machines for cuts from 0° to 60° on the left are also supplied in a version with HB device to make single cuts without operators, still keeping the manual cutting cycle available (the HB device is available only in the three-phase version). HB CUTTING CYCLE: After positioning the bar and closing the vice, the cutting phase is started, using the weight of the saw frame controlled by a hydraulic circuit to adjust the downfeed speed; after the cut the band stops, the frame is manually lifted in order to reposition the bar to cut untill the position needed by the operator.

PH261-1 HB

The PH 261-1 HB, manual band sawing machines for cuts from 0° to 60° on the left are also supplied in a version with HB device to make single cuts without operators, still keeping the manual cutting cycle available ( the HB device is available only in the three-phase version). HB CUTTING CYCLE: After positioning the bar and closing the vice, the cutting phase is started, using the weight of the saw frame controlled by a hydraulic circuit to adjust the downfeed speed; after the cut the band stops, the frame is manually lifted in order to reposition the bar to cut untill the position needed by the operator.

PH262/HB

The PH 262/HB, manual band sawing machines for cuts from -45° to +60°.
Other than the manual cut mode, the sawing machine can make single cuts without operator.

SHARK 281 CCS

SHARK 281 CCS (Cut Control System) manual bandsawing machine to cut from 0° up to 60° left. Other than the manual cut mode, the sawing machine can make single cuts without operator, using the head weight control- led by a hydraulic brake: after the cut the band stops. The frame at this point is manually lifted to the position needed in order to reposition the bar to cut . In the version with pneumatic vice (MA) the vice is opened/clo- sed by a manually-controlled valve (optional with pedal control).

SHARK 282 CCS

SHARK 282 CCS (Cut Control System) manual bandsawing machine to cut from 45° right up to 60° left. Other than the manual cut mode, the sawing machine can make single cuts without operator, using the head weight controlled by a hydraulic brake: after the cut, the band stops. The frame at this point is manually lifted to the position needed in order to reposition the bar to cut . In the version with pneumatic vice (MA) the vice is opened/closed by a manually-controlled valve (optional with pedal control).

SHARK 332 CCS

SHARK 332 CCS, manual band sawing machine to cut from 60° left to 45° right. This model is available in the manual version or with the Cut Control System (CCS). Functioning of the CCS cycle: after positioning the bar and closing the vice, the cutting phase is started, using the weight of the saw head controlled by a hydraulic braking circuit to adjust the feeding speed; after the cut, the saw head is manually lifted till the position needed for the bar to be fed. In the Shark 332 CCS MA model (pneumatic vice) vice opens/closes by means of a footpedal.

SHARK 332 CCS HYDRA

SHARK 332 CCS hydra, band sawing machine for single cuts without operator from 60° on the left to 45°. CUTTING CYCLE: After positioning the bar, operate through the new console to access the following controls: -vice closing ; -starting the cutting cycle that uses the weight of the head controlled by a hydraulic braking circuit to adjust the feeding speed. After the cut, by the keyboard controls, the operator lifts the head through a hydraulic control unit till the necessary position and opens again the pneumatic vice to enable a new bar feeding.

SHARK 382 CCS HYDRA

SHARK 382 CCS hydra, band sawing machine for single cuts without operator from 60° on the left to 45°. CUTTING CYCLE: After positioning the bar, operate through the new console to access the following controls:- vice closing ;- starting the cutting cycle that uses the weight of the head controlled by a hydraulic braking circuit to adjust the feeding speed. After the cut, by the keyboard controls, the operator lifts the head through a hydraulic control unit till the necessary position and opens again the pneumatic vice to enable a new bar feeding.

SHARK 452-1 CCS

SHARK 452-1 CCS, sawing machine for single cuts without operator with 4500x34x1,1 mm band, for cutting pipes, profiles and beams up to 450×320 mm at 0°. Extremely versatile machine, for cuts between 60° left and 60° right. CUTTING CYCLE: after positioning the bar and closing the vice, the cutting phase is started, using the weight of the saw head controlled by a hydraulic braking circuit to adjust the feeding speed; after the cut, the saw head is manually lifted till the position needed for the beam to be fed.

SHARK 452-1 CCS HYDRA

SHARK 452-1 CCS HYDRA, band sawing machine for single cuts without operator on pipes, profiles and beams, up to 450×320 mm at 0°. Extremely versatile machine, for cuts between 60° on the left and 60° on the right. CUTTING CYCLE: After positioning the bar, operate through the new console to access the following controls: vice closing ;starting the cutting cycle that uses the weight of the arc controlled by a hydraulic braking circuit to adjust the feeding speed.

SHARK 512 CCS HYDRA

SHARK 512 CCS HYDRA, band sawing machine for single cuts without operator on pipes, profiles and beams, up to 510×320 mm at 0°. Extremely versatile machine, for cuts between 60° on the left and 60° on the right. CUTTING CYCLE: After positioning the bar, operate through the new console to access the following controls: vice closing; starting the cutting cycle that uses the weight of the arc controlled by a hydraulic braking circuit to adjust the feeding speed.

MEP SpA - Sede Legale: Via Brera, 3 - 20121 Milano (MI) - R.imprese, C.F. e P.Iva 13051480153 Cap. Sociale Eur 10.372.791,00 int. vers.