PH211-1

The PH 211-1, manual band sawing machines for cuts from 0° to 60° on the left are also supplied in a version with HB device to make single cuts without operators, still keeping the manual cutting cycle available ( the HB device is available only in the three-phase version). HB CUTTING CYCLE: After positioning the bar and closing the vice, the cutting phase is started, using the weight of the saw frame controlled by a hydraulic circuit to adjust the downfeed speed; after the cut the band stops, the frame is manually lifted in order to reposition the bar to cut untill the position needed by the operator.

PH261-1

The PH 261-1, manual band sawing machines for cuts from 0° to 60° on the left are also supplied in a version with HB device to make single cuts without operators, still keeping the manual cutting cycle available ( the HB device is available only in the three-phase version). HB CUTTING CYCLE: After positioning the bar and closing the vice, the cutting phase is started, using the weight of the saw frame controlled by a hydraulic circuit to adjust the downfeed speed; after the cut the band stops, the frame is manually lifted in order to reposition the bar to cut untill the position needed by the operator.

PH262

The PH 262, manual band sawing machines for cuts from -45° to +60° is also supplied in a version with Hydraulic Brake device (HB) to make single cuts without operator but keeping the manual cutting cycle available ( the HB device is available only in the three-phase version).

SHARK 281

SHARK 281, manual band sawing machine to cut from 0° to 60° left. The vice on the pneumatic versions (MA) opens and closes by means of a manually operated valve (or by means of a footpedal which is instead optional). A FEW FEATURES: Electric panel (wiring totally identifiable, stand-by, loose-key safety switch, main switch, pole change switch, emergency stop, motor magneto-thermal overload, minimum tension coil, protection against missing phase, low tension safety device (LTSD 24 V).- IP55 control handle.

SHARK 282

SHARK 282, manual band sawing machine to cut from 45° right to 60° left. The vice on the pneumatic versions (MA) opens and closes by means of a manually operated valve (or by means of a footpedal which is instead optional). A FEW FEATURES: – Hydraulic transducer to visualize band tensioning. – Wire chip brush for band cleaning. – Double head return spring. – Sliding vice with sideways movement and fast-positioning system. – Wide working surface with rotating table installed on a roller bearing, dia. 265 mm, pre-loaded with thrust bearing.

TIGER 352/MA

TIGER 352, manual vertical sawing machine to cut from 60° left to 45° right, with HSS blade. A FEW FEATURES: – Sawing head movement on double linear guides with preloaded slides with recirculating ballscrews. – Electrical panel (wiring totally identifiable, main lockable disconnect switch, motor magneto-thermal overlo- ad, minimum tension coil, protection against missing phase, low tension safety device 24 V). – Low voltage IP55 control handle. – Rotating table on a center pin with axial bearing which allows higher precision on the cutting angle set. – Double set of gears to obtain a high performance.

FALCON 251

FALCON 251, small manual pivot sawing machine to cut metals from 0° to 45° left, using an HSS blade. Practical and safe to use, it can be supplied as a bench model or with the steel base, with three-phase or single-phase speed motor. A FEW FEATURES: – Electric system: wiring totally identifiable, motor switch, low tension safety device (LTSD 24 V) with IP55 control handle for the three-phase version and IP55 control handle for the single-phase version.- Metal blade cover which totally encloses the blade. – Double head return spring. – Bronze gear and casehardened/grounded worm screw which work immersed in oil.

FALCON 302

FALCON 302, manual sawing machine to cut metals from 45° right to 45° left using an HSS blade. This high performance model has a heavy cast iron structure and is equipped with all the devices and functions neces- sary so as to cut in a precise and safe manner. FALCON 302 is available as a bench model or eventually with the steel base. Furthermore it can be supplied with three-phase motor at one or two speeds. A FEW FEATURES: – Blade shaft assembled on spheroidal cast iron eccentric bushing. – Bronze gear mounted with key and ring nut so as to grant the maximum hold.- Worm screw shaft mounted on a pair of bushings.

FALCON 352/MA

FALCON 352, manual sawing machine to cut metals from 45° right to 45° left using an HSS blade. This high performance model has a heavy cast iron structure and is equipped with all the devices and functions neces- sary so as to cut in a precise and safe manner. FALCON 352 is available as a bench model or eventually with the steel base, with a 2-speed three-phase motor. Furthermore upon request it can be supplied with an automatic vice (FALCON 352 MA, so that the vice closes automatically when lowering the head). In the MA version the machine is always supplied complete with steel base. A FEW FEATURES: – Motor insulation class IP54.

COBRA 352/MA

COBRA 352, manual sawing machine to cut aluminium and light alloys using blade with electrowelded hard-metal plates. The machine cuts from 45° right to 45° left with the head which can be tilted from 0° to 45° left. On the model 352 MA (pneumatic vice), which is supplied complete with steel base, the vices close automati- cally when lowering the head.

WILLY 225

WILLY 225, small sawing machine, bench model, with HSS blade, to cut from 0° to 45°left. Model for hobbyists and fitters, entirely built in cast iron and available in 1-speed single-phase version. A FEW FEATURES: – Bronze gear and casehardened/grounded worm screw which work immersed in oil. – The head which swivels is locked by means of a screw so as to mitre cut. – Control handle IP55 with 20-A microswitch to start/stop blade.

MEP SpA - Sede Legale: Via Brera, 3 - 20121 Milano (MI) - R.imprese, C.F. e P.Iva 13051480153 Cap. Sociale Eur 10.372.791,00 int. vers.